Release 0.3.1 (released Feb 5, 2021)¶
Bug Fixes in 0.3.1¶
Fixes a typo in labgrid-bound-connect, which should re-enable connection proxying for SSH.
Man-Pages have been correctly regenerated.
The exporter correctly handles the configured baud-rate for serial ports again.
Various tests have been marked with skips if the modules are not available.
Docker files have been moved to from the docker directory to the dockerfiles directory, which prevents the tests from incorrectly assuming a docker module is available.
Release 0.3.0 (released Jan 22, 2021)¶
New Features in 0.3.0¶
CommandProtocoldrivers support the poll_until_success method.
FileDigitalOutputDriverrespresents a digital signal with a file.
GpioDigitalOutputDrivercontrols the state of a GPIO via the sysfs interface.
Crossbar and autobahn have been updated to 19.3.3 and 19.3.5 respectively.
The InfoDriver was removed. The functions have been integrated into the labgridhelper library, please use the library for the old functionality.
write-imagesubcommand: labgrid client now has a
write-imagecommand to write images onto block devices.
labgrid-client sshnow also uses port from NetworkService resource if available
STATEvariables used by labgrid-client are replaced by
LG_STATE, the old variables are still supported for the time being.
The SSHDriver’s keyfile attribute is now specified relative to the config file just like the images are.
The ShellDriver’s keyfile attribute is now specified relative to the config file just like the images are.
labgrid-client -P <PROXY>and the
LG_PROXYenviroment variable can be used to access the coordinator and network resources via that SSH proxy host. Drivers which run commands via SSH to the exporter still connect directly, allowing custom configuration in the user’s
.ssh/configas needed. Note that not all drivers have been updated to use the ProxyManager yet.
Deditec RELAIS8 devices are now supported by the
RKUSBDriverwas added to support the rockchip serial download mode.
USBStorageDrivergained support for BMAP.
Flashrom support added, by hard-wiring e.g. an exporter to the DUT, the ROM on the DUT can be written directly. The flashrom driver implements the bootstrap protocol.
AndroidFastbootDriver now supports ‘getvar’ and ‘oem getenv’ subcommands.
The coordinator now updates the resource acquired state at the exporter. Accordingly, the exporter now starts ser2net only when a resources is aquired. Furthermore, resource conflicts between places are now detected.
Labgrid now uses the
ProcessWrapperfor externally called processes. This should include output from these calls better inside the test runs.
The binding dictionary can now supports type name strings in addition to the types themselves, avoiding the need to import a specific protocol or driver in some cases.
The remote infrastructure gained support for place reservations, for further information check the section in the documentation.
SigrokDrivergained support for the Manson HCS-2302, it allows enabling and disabling channels, measurement and setting the current and voltage limit.
labgrid-client write-imagegained new arguments:
Support for Sentry PDUs has been added.
Strategies now implement a
forcea strategy state irrespective of the current state.
SSH Connections can now be proxied over the exporter, used by adding a device suffix to the
UBootDriver now allows overriding of default boot command (
run bootcmd) via new
The config file supports per-target options, in addition to global options.
Add power driver to support GEMBIRD SiS-PM implementing SiSPMPowerDriver.
A cleanup of the cleanup functions was performed, labgrid should now clean up after itself and throws an error if the user needs to handle it himself.
labgrid-clientnow respects the
LG_USERNAMEenvironment variables to set the hostname and username when accessing resources.
PyVISA support added, allowing to use PyVISA controlled test equipment from Labgrid.
labgrid-client write-imagegained a new argument
--modeto specify which tool should be used to write the image (either
Exporter configuration file
exporter.yamlnow allows use of environment variables.
Breaking changes in 0.3.0¶
ManagedFilenow saves the files in a different directory on the exporter. Previously
/tmpwas used, labgrid now uses
/var/cache/labgrid. A tmpfiles example configuration for systemd is provided in the
/contribdirectory. It is also highly recommended to enable
fs.protected_fifos=1for kernels>=4.19. This requires user intervention after the upgrade to create the directory and setup the cleanup job.
@attr.s(cmp=False)is deprecated and all classes have been moved to
@attr.s(eq=False), this release requires attrs version 19.2.0
Coordinator work dir is now set to the same dir as the crossbar configuration dir. Hence coordinator specific files like
resources.yamlare now also stored in the crossbar configuration folder. Previously it would use
USBStickclasses have been removed
Known issues in 0.3.0¶
There are several reports of
sshpassused within the SSHDriver not working in call cases or only on the first connection.
Some client commands return 0 even if the command failed.
Currently empty passwords are not well supported by the ShellDriver
Release 0.2.0 (released Jan 4, 2019)¶
New Features in 0.2.0¶
A colored StepReporter was added and can be used with
labgrid-clientcan now use the last changed information to sort listed resources and places.
labgrid-client sshnow uses ip/user/password from NetworkService resource if available
The pytest plugin option
--lg-logenables logging of the serial traffic into a file (see below).
The environement files can contain feature flags which can be used to control which tests are run in pytest.
LG_*variables from the OS environment can be used in the config file with the
The new “managed file” support takes a local file and synchronizes it to a resource on a remote host. If the resource is not a
NetworkResource, the local file is used instead.
ProxyManager: a class to automatically create ssh forwardings to proxy connections over the exporter
SSHManager: a global manager to multiplex connections to different exporters
The target now saves it’s attached drivers, resources and protocols in a lookup table, avoiding the need of importing many Drivers and Protocols (see Syntactic sugar for Targets)
When multiple Drivers implement the same Protocol, the best one can be selected using a priority (see below).
The new subcommand
labgrid-client monitorshows resource or places changes as they happen, which is useful during development or debugging.
The environment yaml file can now list Python files (under the ‘imports’ key). They are imported before constructing the Targets, which simplifies using custom Resources, Drivers or Strategies.
The pytest plugin now stores metadata about the environment yaml file in the junit XML output.
labgrid-clienttool now understands a
--stateoption to transition to the provided state using a
Strategy. This requires an environment yaml file with a
RemotePlaceResources and matching Drivers.
Resource matches for places configured in the coordinator can now have a name, allowing multiple resources with the same class.
Target.__getitem__method makes writing using protocols less verbose.
Experimental: The labgrid-autoinstall tool was added (see below).
New and Updated Drivers¶
DigitalOutputResetDriveradapts a driver implementing the DigitalOutputProtocol to the ResetProtocol.
ModbusCoilDriversupport outputs on a ModbusTCP device.
NetworkUSBStorageDriverallows writing to remote USB storage devices (such as SD cards or memory sticks connected to a mux).
QuartusHPSDrivercontrols the “Quartus Prime Programmer and Tools” to flash a target’s QSPI.
SerialPortDigitalOutputDrivercontrols the state of a GPIO using the control lines of a serial port.
SigrokDriveruses a (local or remote) device supported by sigrok to record samples.
SmallUBootDriversupports the extremely limited U-Boot found in cheap WiFi routers.
USBSDMuxDrivercontrols a Pengutronix USB-SD-Mux device.
USBTMCDrivercan fetch measurements and screenshots from the “Keysight DSOX2000 series” and the “Tektronix TDS 2000 series”.
USBVideoDrivercan stream video from a remote H.264 UVC (USB Video Class) camera using gstreamer over SSH. Currently, configuration for the “Logitech HD Pro Webcam C920” exists.
XenaDriverallows interacting with Xena network testing equipment.
The bootloader drivers now have a
BareboxDriver’s boot string is now configurable, which allows it to work with the
quietLinux boot parameter.
IMXUSBLoadernow recognizes more USB IDs.
OpenOCDDriveris now more flexible with loading configuration files.
NetworkPowerDrivernow additionally supports:
24 port “Gude Expert Power Control 8080”
8 port “Gude Expert Power Control 8316”
NETIO 4 models (via telnet)
a simple REST interface
SerialDrivernow supports using plain TCP instead of RFC 2217, which is needed from some console servers.
ShellDriverhas been improved:
It supports configuring the various timeouts used during the login process.
It can use xmodem to transfer file from and to the target.
When using the coordinator, it must be upgrade together with the clients because of the newly introduce match names.
Resources and Drivers now need to be created with an explicit name parameter. It can be
Noneto keep the old behaviour. See below for details.
Syntactic sugar for Targets¶
Targets are now able to retrieve requested drivers, resources or protocols by name instead of by class. This allows removing many imports, e.g.
from labgrid.driver import ShellDriver shell = target.get_driver(ShellDriver)
shell = target.get_driver("ShellDriver")
Also take a look at the examples, they have been ported to the new syntax as well.
Multiple Driver Instances¶
For some Protocols, it is useful to allow multiple instances.
A board may have two jumpers to control the boot mode in addition to a reset GPIO. Previously, it was not possible to use these on a single target.
Some boards have multiple console interfaces or expose a login prompt via a USB serial gadget.
In some cases, multiple power ports need to be controlled for one Target.
To support these use cases, Resources and Drivers must be created with a
When updating your code to this version, you can either simply set the name to
None to keep the previous behaviour.
Alternatively, pass a string as the name.
>>> t = Target("MyTarget") >>> SerialPort(t) SerialPort(target=Target(name='MyTarget', env=None), state=<BindingState.bound: 1>, avail=True, port=None, speed=115200) >>> SerialDriver(t) SerialDriver(target=Target(name='MyTarget', env=None), state=<BindingState.bound: 1>, txdelay=0.0)
New (with name=None):
>>> t = Target("MyTarget") >>> SerialPort(t, None) SerialPort(target=Target(name='MyTarget', env=None), name=None, state=<BindingState.bound: 1>, avail=True, port=None, speed=115200) >>> SerialDriver(t, None) SerialDriver(target=Target(name='MyTarget', env=None), name=None, state=<BindingState.bound: 1>, txdelay=0.0)
New (with real names):
>>> t = Target("MyTarget") >>> SerialPort(t, "MyPort") SerialPort(target=Target(name='MyTarget', env=None), name='MyPort', state=<BindingState.bound: 1>, avail=True, port=None, speed=115200) >>> SerialDriver(t, "MyDriver") SerialDriver(target=Target(name='MyTarget', env=None), name='MyDriver', state=<BindingState.bound: 1>, txdelay=0.0)
Each driver supports a priorities class variable.
This allows drivers which implement the same protocol to add a priority option
to each of their protocols.
This way a
NetworkPowerDriver can implement the
ResetProtocol, but if another
ResetProtocol driver with a higher protocol is available, it will be selected
See the documentation for details.
The ConsoleLoggingReporter can be used with the pytest plugin or the library. It records the Data send from a DUT to the computer running labgrid. The logfile contains a header with the name of the device from the environment configuration and a timestamp.
When using the library, the reporter can be started with:
from labgrid.consoleloggingreporter import ConsoleLoggingReporter ConsoleLoggingReporter.start(".")
where “.” is the output directory.
The pytest plugin accepts the
--lg-log commandline option, either with or
without an output path.
To simplify using labgrid for provisioning several boards in parallel, the
labgrid-autoinstall tool was added.
It reads a YAML file defining several targets and a Python script to be run for
Interally, it spawns a child process for each target, which waits until a matching
resource becomes available and then executes the script.
For example, this makes it simple to load a bootloader via the
BootstrapProtocol, use the
AndroidFastbootDriver to upload a
kernel with initramfs and then write the target’s eMMC over a USB Mass Storage
labgrid-autoinstall is still experimental and no documentation has been written.
Contributions from: Ahmad Fatoum, Bastian Krause, Björn Lässig, Chris Fiege, Enrico Joerns, Esben Haabendal, Felix Lampe, Florian Scherf, Georg Hofmann, Jan Lübbe, Jan Remmet, Johannes Nau, Kasper Revsbech, Kjeld Flarup, Laurentiu Palcu, Oleksij Rempel, Roland Hieber, Rouven Czerwinski, Stanley Phoong Cheong Kwan, Steffen Trumtrar, Tobi Gschwendtner, Vincent Prince
Release 0.1.0 (released May 11, 2017)¶
This is the initial release of labgrid.